Menu
(951) 345-3509Discuss a project

Lower Mississippi and Gulf Coast · in-situ field survey

Wenner four-pin soil resistivity testing in New Orleans

Field measurements for grounding studies, substations, solar and battery facilities, transmission, utilities, buried assets, and corrosion evaluations.

Request a survey scope Wenner knowledge center

Regional planning context

Why the earth profile has to be measured at the project

New Orleans construction can involve deltaic clay and silt, organic material, hydraulic fill, and shallow groundwater. Wenner field work should document hydraulic fill, imported material, and current moisture rather than assume naturally wet conditions remain permanent.

Regional descriptions help identify station coverage, candidate line directions, and likely changes along an alignment. They do not provide a design resistivity for a parcel or route. A Wenner result is apparent soil electrical resistivity for the documented array and field condition.

Field method

What the Wenner array measures

Four small electrodes are installed in a straight line at equal spacing. The instrument sends current through the outer pair and measures voltage between the inner pair. Measured resistance and array geometry are used to calculate apparent soil electrical resistivity.

Readings are repeated at a planned spacing sequence and, when needed, at multiple locations or orientations. Larger spacing investigates a larger earth volume, while changes in the apparent-resistivity curve can indicate nonuniform ground that the grounding engineer may model as layers.

The method records the earth response; it does not by itself select a ground grid, predict touch and step voltage, establish corrosion rate, or design cathodic protection. Those decisions use the field dataset together with the asset geometry and governing design method.

Regional applications

Where soil electrical resistivity data is commonly used

The receiving engineer defines the spacing, station density, model, and acceptance needs for the specific asset.

01

grounding studies for port and terminal electrical systems

A project-specific survey can map multiple locations and spacings while preserving geometry, site condition, and observed interference for this New Orleans application.

02

Wenner route surveys for stormwater and water-infrastructure power feeds

A project-specific survey can map multiple locations and spacings while preserving geometry, site condition, and observed interference for this New Orleans application.

03

buried-utility corrosion evaluation for utility-hardening and underground distribution

A project-specific survey can map multiple locations and spacings while preserving geometry, site condition, and observed interference for this New Orleans application.

Station to report

How a field survey is completed

A useful dataset begins before the first electrode is driven.

  1. 01

    Define the use

    Identify the grounding, corrosion, route-comparison, investigation, or owner requirement and the engineer who will receive the data.

  2. 02

    Plan stations and spacings

    Overlay the facility, grading, utilities, buried metal, overhead conductors, access, terrain, and candidate straight corridors.

  3. 03

    Clear and lay out each line

    Confirm utility clearance, station coordinates, orientation, surface condition, line length, and deviations before installing electrodes.

  4. 04

    Measure and repeat

    Collect resistance readings at the planned equal spacings, verify units and connections, repeat questionable points, and document noise or contact problems.

  5. 05

    Issue traceable data

    Report raw readings, calculated apparent resistivity, locations, alignment, spacing, field condition, photographs, deviations, and limitations.

Scope checklist

Information to send before mobilization

Call (951) 345-3509 or email info@soiltestslab.com with the plans. Calicore can help translate a general request into a station and spacing matrix.

Frequently asked

New Orleans Wenner testing questions

Is there a typical soil resistivity for New Orleans?+

No citywide value can represent a parcel, substation, route, or facility. New Orleans construction can involve deltaic clay and silt, organic material, hydraulic fill, and shallow groundwater. Wenner field work should document hydraulic fill, imported material, and current moisture rather than assume naturally wet conditions remain permanent. Field measurements must be tied to the actual array, location, spacing, orientation, and current condition.

Does Wenner electrode spacing equal test depth?+

No. Larger spacing generally samples a larger earth volume, but spacing is not an exact one-to-one depth. Layering, array geometry, site boundaries, and conductive features affect the apparent response.

What information is needed to scope a New Orleans survey?+

Send the site plan, survey objective, grounding or corrosion design request, proposed stations and spacings, final grading information, candidate line corridors, utility-clearance responsibility, access rules, schedule, and required report format.

Can Calicore mobilize outside California?+

Yes. Calicore performs project-based Wenner field programs throughout the United States when the station count, spacing, access, schedule, and mobilization are practical.

Technical starting points

Methods, maps, and field context

Maps and climate information guide station planning only. They cannot replace field measurements or establish a parcel-wide electrical resistivity.

Nearby and related markets

More regional Wenner survey guides

View all U.S. locations
LouisianaBaton RougeNew MexicoAlbuquerqueAlaskaAnchorageGeorgiaAtlantaTexasAustin

Nationwide field surveys

Build a usable station and spacing plan before the crew travels.

Send the site plan, design use, requested stations and spacings, site access, utility-clearance process, construction stage, and schedule.

Request a proposal